Kit Review – SC/Jaycar USB Power Monitor

Introduction

Every month Australian electronics magazine Silicon Chip publishes a variety of projects, and in December 2012 they published the USB Power Monitor by Nicholas Vinen. Jaycar picked it up and now offers a kit, the subject of our review. This small device plugs inline between a USB port and another device, and can display the current drawn, power and voltage at the USB port with a large LCD module. This is useful when you’re experimenting with USB-powered devices such as Arduino projects or curious how external USB devices can affect your notebook computer’s battery drain.

Assembly

The kit arrives in typical Jaycar fashion:

… everything necessary is included with the kit:

The instructions arrive as an updated reprint of the original magazine article, plus the usual notes from Jaycar about warranty and their component ID sheet which is useful for beginners. The PCB is quite small, and designed to be around the same size as the LCD module:

As you can see below, most of the work is already done due to the almost exclusive use of SMD components:

That’s a good thing if you’re in a hurry (or not the best with surface-mount work). Therefore the small amount of work requires is simply to solder in the USB sockets, the button and the LCD:

It took less than ten minutes to solder together. However – take careful, careful note of the LCD. There isn’t a pin 1 indicator on the module – so instead hold the LCD up to the light and determine which side of the screen has the decimal points – and line it up matching the silk-screening on the PCB. Once finished you can add the clear heatshrink to protect the meter, but remember to cut a small window at the back if you want access to the ICSP pins for the PIC microcontroller:

How it works

The USB current is passed through a 50 mΩ shunt resistor, with the voltage drop being measured by an INA282 current shunt monitor IC. The signal from there is amplified by an op amp and then fed to the ADC of a PIC18F45K80 microcontroller, which does the calculations and drives the LCD. For complete details purchase the kit or a copy of the December 2012 edition of Silicon Chip.

Operation

First you need to calibrate the unit – when first used the meter defaults to calibration mode. You simply insert it into a USB port. then measure the USB DC voltage brought out to two pads on the meter. By pressing the button you can match the measured voltage against the display as shown below – then you’re done.

Then you simply plug it in between your USB device and the socket. Press the button to change the measurement. The meter can measure the following ranges:

For an operational example. consider the next three images are from charging my phone – with the power, current and voltage being shown:

“P” for power…

current in mA

“b” for bus voltage

If you want to use the USB ports on the right-hand side of your computer, just press the button while inserting the meter – and it flips around:

Finally – here’s a quick video of the meter at work, whilst copying a file to an external USB hard drive:

Conclusion

I really like this – it’s simple and it works. Kudos to Nicholas for his project. You can purchase it from Jaycar and their resellers, or read more about it in the December 2012 edition of Silicon Chip. Full-sized images available on flickr. This kit was purchased without notifying the supplier.

In the meanwhile have fun and keep checking into tronixstuff.com. Why not follow things on twitter, Google+, subscribe  for email updates or RSS using the links on the right-hand column? And join our friendly Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Welcome to “Silicon Chip” Magazine readers

Hello readers

Published in the January 2012 issue of “Silicon Chip” magazine is an eight page feature article by Jonathan Oxer introducing the Arduino system and how the hardware and software work together to allow anyone to turn their technological ideas into reality. If you have read Jon’s article and were directed here – thanks for visiting! We have much more content than just Arduino tutorials, however to get started with them please click here or select from one of the chapters listed in the “Arduino Tutorials” section on the right-hand side of this web page.  Our site is a work in progress and if you have any feedback or questions please email john at tronixstuff dot com, or visit our moderated Google Group.

Be sure to take advantage of the discount code on page seventeen made available by Little Bird Electronics - Australia’s largest Arduino and related electronics distributor; and also check out the range of Arduino-compatible equipment at Freetronics.

For those not familiar with the magazine, here is the cover for the January 2012 issue:

So what is “Silicon Chip” magazine all about? It is Australia’s window to the wide world of electronics, backed by a team of engineers and enthusiasts with decades of experience and knowledge. Each month you can read about in-house projects by the team and also submitted by readers – covering basic circuits right through to digital and computer systems, quality hi-fi and audio projects, news, reviews, readers’ letters, the humorous columns and a wide variety of kits to assemble. There is also a wide range of advertising from related businesses that helps you find new products and suppliers that you may not have known about.

Silicon Chip is the only Australian electronics magazine and one of the few left in the world with a broad appeal to the beginner and expert alike, and the projects described are always good value and not priced or designed out of most peoples’ reach. I unashamedly recommend you pick up a copy from the newsagent or take out a subscription if possible, it’s a great read and there’s always lots to learn and laugh about.

Finally, that’s it for 2011. A big thank you to all of our readers for your visits, feedback, compliments, criticism, donations, and the crazy emails received through the year. And of course to all the great suppliers who help out with promotional considerations and sponsor our monthly competitions. Keeping this site together has been interesting, educational and a whole lot of fun, and I hope you think so too. There is a lot coming up for 2012 – so stay tuned via twitter, Google+, or subscribe by email or RSS on the right-hand side of this page.

Have fun and Happy New Year

John Boxall.

Project – Simple RFID access system

In this tutorial you can make an RFID access system. It’s very simple and can be used with a wide variety of end-uses.

Updated 18/03/2013

The purpose of this project is to prototype a basic RFID access system. Although it is not that complicated, this article is my response to a kit reviewed in the Australian “Silicon Chip” (November 2010) electronics magazine. Their article describes the kit in detail – operation, schematic, use and installation. However the code for the microcontroller (PIC16F628A)  is not published due to the kit manufacturer holding copyright over the design. This is a shame, as many organisations have been quite successful selling open-source kits. So instead of moaning about it, I have created my own design that matches the operation of the original, instead using the ATmega328 MCU with Arduino bootloader. Consider this a basic framework that you can modify for your own access system, or the start of something more involved.

original article

There are pros and cons with the original vs. my version. The biggest pro is that you can buy the whole kit for around Au$40 including a nice PCB, solder it together, and it works. However if you want to do it yourself, you can modify it to no end, and have some fun learning and experimenting along the way. So let’s go!

The feature requirements are few. The system must be able to learn and remember up to eight RFID access tags/cards, etc – which must be able to be altered by a non-technical user. Upon reading a card, the system will activate a relay for a period of time (say 1 second) to allow operation of a door strike or electric lock. Finally, the RFID tag serial numbers are to be stored in an EEPROM in case of a power outage. When a tag is read, a matching LED (1~8) will show which tag was read. There are also two LEDs, called “Go” and “Stop” which show the activation status. The original kit has some more LEDs, which I have made superfluous by blinking existing LEDs.

This is a simple thing to make, and the transition from a solderless breadboard to strip board will be easy for those who decide to make a permanent example. But for now, you can follow with the prototype. First is the parts list:

• Atmel ATmega328 with Arduino bootloader;
• 16 MHz resonator (X1 in schematic);
• ten LEDs of your choice;
• two normally-open push buttons;
• two 560 ohm resistors (all resistors 1/4 watt);
• one 1k ohm resistor;
• three 10k ohm resistors;
• one BC548 transistor;
• three 0.01 uF monolithic capacitors;
• one 100 uF electrolytic capacitor;
• one 1N4004 diode;
• Microchip 24LC256 EEPROM;
• 125 kHZ RFID module;
• 125 kHz RFID tags/cards;
• connecting wire;
• large solderless breadboard;
• LM7805 power regulator;
• relay of your choice with 5V coil (example).

When selecting a relay, make sure it can handle the required load current and voltage – and that the coil current is less than 100mA.

If attempting to switch mains voltage/current – contact a licensed electrician. Your life is worth more than the money saved by not consulting an expert.

And here is the schematic:

Here is the prototype on the solderless breadboard. For demonstration purposes an LED has been substituted for the transistor/relay section of the circuit, the power regulator circuitry has not been shown, and there are superfluous 4.7k resistors on the I2C bus. To program the software (Arduino sketch) the easiest way is by inserting the target IC into an Arduino-compatible board, or via a 5V FTDI cable and a basic circuit as described here.

The Arduino sketch is also quite simple. The main loop calls the procedure readTags() to process any RFID tag read attempts, and then monitors button A – if pressed, the function learnTags() is called to allow memorisation of new RFID tags. Each tag serial number consists of 14 decimal numbers, and these are stored in the EEPROM sequentially. That is, the first tag’s serial number occupies memory positions 0~13, the second tag’s serial number occupies memory position 14~28, and so on. Two functions are used to read and write tag serial numbers to the EEPROM – readEEPROMtag() and writeEEPROMtag(). The EEPROM is controlled via the I2C bus. For a tutorial about Arduino, I2C bus and the EEPROM please read this article. For a tutorial about Arduino and RFID, please read this article. The rest of the sketch is pretty self-explanatory. Just follow it along and you can see how it works. You can download the sketch from here.

 
And finally, a quick video demonstration:

So there you have it. I hope you enjoyed reading about this small project and perhaps gained some use for it of your own or sparked some other ideas in your imagination that you can turn into reality.

In the meanwhile have fun and keep checking into tronixstuff.com. Why not follow things on twitter, Google+, subscribe  for email updates or RSS using the links on the right-hand column? And join our friendly Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.