Kit Review – adafruit industries mintyboost v3
Today we are going introduce another useful kit from adafruit industries – their mintyboost kit. The purpose of this kit is to provide a powered USB socket suitable for charging a variety of devices, powered from a pair of AA cells. The mintyboost is quite a simple, yet clever design – the latest version is based around the Linear Technology LT1302 DC/DC step-up converter that we examined a few months ago - and can provide a full 5 volts DC at 500 milliamps, enough to charge the latest round of USB-chargable gadgets, including those iPhones that I keep hearing about. And unlike an iPhone, the mintyboost kit is licensed under a Creative Commons v2.5 attribution license.
But enough reading, time to make it. As always, instructions are provided online – are easy to follow and very clear. The kit will arrive in a nice reusable anti-static bag:
Which contains everything you need except for AA cells and a housing:
Where or how you contain your mintyboost is a subjective decision, and will probably vary wildly. The original design brief was to have it fit inside a tin that Altoids confectionary is sold in, however those are not available around my area. But I found a suitable replacement. The PCB is very small, and designed to fit snugly inside the aforementioned tin:
Very small – less than 38 x 20 mm in dimension. However with some care and caution, you can solder the components without using a vice or “helping hands”. Though if you have access to these, use them as it will make life a lot easier. Before we move on, please note that my 49.9k ohm resistors, ceramic capacitors and the inductor are a different size to those included with the kit. This is my second mintyboost, and to save money I bought the PCB only and used my own parts to make this one.
If size is an issue for you, it is a good idea to buy the entire kit, as you will have resistors that fit flush with the PCB, unlike mine
However, construction moved along smoothly, by following the instructions, double-checking my work and not rushing things. There is some clever designing going on here, I have never seen a resistor underneath an IC socket before!
But when PCB real estate is at a premium, you need think outside of the box. After this stage there was just the electrolytic capacitors and battery holder to install. One that has been done, you can insert some fresh AA cells and check the output voltage on the USB lines:
Looking good, however it could have been a bit higher if the AA cells were freshly charged. But the second USB voltage was spot on:
Success! It always feels good to make a kit and have it work the first time. The last soldering was to take care of fitting the USB socket, and then it was finished:
Now to take it for a test run. I have two USB-charging items to test it with, my HTC Desire:
The LED to the right of the htc logo indicates the power is in, and the battery indicator on the left of the clock indicates charging. Excellent. The phone battery is 1400 mAh – I most likely won’t get a full recharge from the two AA cells, but enough to get me through an extra night and half a day. The mintyboost is a perfect backup-charging solution to leave in your backpack or other daily case. And now for something from Apple, an iPod of about four years old (it still holds a charge, so I’m not falling for the “buy a new iPod every twelve months” mantra):
Again, perfect. Apple equipment can be quite finicky about the voltages being fed to them, and will not work if there is a slight difference to what the device expects to be fed. As you can see the team at adafruit have solved this problem nicely. There is also much discussion about various devices and so on in their support forums.
Now for the decision with regards to housing my mintyboost. The Altoids tins are not an option, and I’m not cannibalising my mathematical instruments storage tin. But I knew I kept this tin for a reason from last February:
Plenty of room for the PCB, the charging cable, emergency snack cash and even more AA cells if necessary. And where else could I have put the socket, but here:
I have named it the bunnyboost:
… who can safely live in the bottom of my backpack, ready to keep things powered at a moments’ notice. Excellent!
As you can see, the mintyboost is a simple, yet very practical kit. It would also make a great gift for someone as well, as USB-charging devices are becoming much more popular these days. If you are looking to buy a kit, those of you in the Australasian market can get one from Little Bird Electronics, or globally available from adafruit industries.
Once again, thank you for reading and I look forward to your comments and so on. Please subscribe using one of the methods at the top-right of this web page to receive updates on new posts, and if you have any questions – why not join our Google Group? It’s free and we’re all there to learn and help each other.
High resolution photos are available on flickr.
[Note - this kit was purchased by myself personally and reviewed without notifying the manufacturer or retailer]